Introduction

Once actual construction is completed you will want to connect the rig to the outside world. The possible connections (depending upon your use - here we assume you will be using Rocky for RX, TX, PTT, and keyer) are:

  • Power (right-hand edge of the board, near the top)
  • Antenna (ANT/RET - right hand edge, near half-way down)
  • Keyer (right hand edge, just below antenna connection. Three terminals: C=common, .=dot, -=dash)
  • Serial Connection (for PTT and/or keyer - right-hand edge of the board, at bottom)
  • TX I and Q audio inouts (left-hand edge, near top - Ring, Tip, and ground)
  • RX I and Q audio outputs (left-hand edge, near bottom - Ring and Tip)

Connection Locations

Summary Build Notes

  • Install RX I/Q leads
  • Install TX I/Q leads
  • Install antenna leads
  • Install Power leads
  • Install keyer connection
  • Install Rocky serial interface leads and socket

Detailed Build Notes

Audio (I/Q) Connection

I Q Out COnnection
Sample audio cable connection

RX I and Q Audio output - LINE IN

These are the Ring(Q) and Tip audio outputs of the board, located at the bottom left edge of the board.

Depending upon your ultimate enclosure/mounting requirements, you want to connect these three pads to good quality shielded 2 conductor audio cable, terminated either by a 3.5 mm mini plug or a mini jack.
Use a short length of solid hookup wire, soldered to the shielding and to the ground/common connection, and wrapped firmly around the outer insulation of the cable as a strain relief mechanism.

If you plan on using the same sound card for both the RX and TX I and Q signals, you can reduce the possibility of ground loops (and the attendant noise in your RX) by NOT grounding the RX cable's shield and, instead, sharing the common ground in the TX cable. If you do this and you mount a stereo jack in your metal enclosure, you should be sure to use an isolated stereo jack for your RX output jack, such as the Markertek 30-711 jack

TX I and Q Audio input - "L - R"

These are the Left and Right audio outputs of the PC when in transmit mode. The connection points located at the top left edge of the board.

Depending upon your ultimate enclosure/mounting requirements, you want to connect these three pads to good quality shielded 2 conductor audio cable, terminated either by a 3.5 mm mini plug or a mini jack.
Use a short length of solid hookup wire, soldered to the shielding and to the ground/common connection, and wrapped firmly around the outer insulation of the cable as a strain relief mechanism.

If you plan on using the same sound card for both the RX and TX I and Q signals, you can reduce the possibility of ground loops by NOT grounding the RX cable's shield and, instead, sharing the common ground in the TX cable. If you do this and you mount a stereo jack in your metal enclosure, you should be sure to use an isolated stereo jack, such as the Markertek 30-711 jack

Experiment with various grounding/connection configurations to give the least disturbance around the center frequency. Get it right before boxing it up in an enclosure.

Antenna Connection

Antenna Connection
Sample Antenna Connection

ANT/RET

These are the ANT and Ground (unmarked) connections located on the right-hand side of the board, near the top.

Use RG-174U 50 ohm "micro" coax for the antenna connection, There is a good discussion of RG-174 coax and techniques for installing connectors available on the internet.

Use the strain-relief technique illustrated above.

Power Connection

Power Connection
Sample Power Connection

PWR


Use the conventional red/black wire for the power line +/- connections with the connector of your choice.

Keyer Connection

Keyer Connection
Keyer Connection Leads

KEY

This works for your keyer, providided you have also connected the serial connector from Rocky. Connect leads from your keyer's common, dot, and dash lines to the corresponding points just below the antenna connection.

If you plan to mount a stereo jack in your metal enclosure to connect the keyer plug, be sure to use an isolated jack in order to eliminate ground loops.

Rocky Serial Interface Connection

Keyer Connection
DB9 Connector Location

DB9

This provides PTT signals from and, optionally, keyer dots and dashes to, Rocky through a standard DB9 connector.  Plug the serial connector from your PC (directly or via a USB-to-Serial adaptor) into the DB9 connector wired into the holes at the bottom right edge of the board.

The SRv6.3 PTT_I can be activated with from +4.5 to +12 Vdc